ATE LC15 wall drying device

Electromagnetic device for walls affected by rising damp

Coverage diameter: 15 mMains-powered

ATE LC15: a device for damp walls

We manufacture the ATE LC15 in France to support the progressive drying of walls affected by rising damp. Its 15 m coverage diameter helps you choose a model suited to your building’s layout.

What area can it cover?

The stated diameter is 15 m, equivalent to a radius of 7.5 m. Check that this reach covers the affected zone. A diameter is not a floor area measured in square metres.

Operation and installation

The device operates continuously when connected to mains power. Fixing and electrical connection must follow our installation manual. No chemical injection into the walls is required.

How long can drying take?

The 18–24 month period is indicative. Progress depends on the materials, wall thickness, ventilation and installation conditions. It does not guarantee complete drying within a fixed period.

Check the cause of the damp

Our devices are intended for rising damp. Water ingress, leaks and condensation require solutions appropriate to their causes.

The reliable warranty you need

  • 10-year manufacturer’s warranty
  • Made in France
  • Designed and developed by our team
  • Direct sales from our factory
  • Advice and assistance from our team
ATE LC15 – ATE LC15 wall drying device

Simple and practical to use

  • Coverage diameter: 15 m
  • Installation according to our manual
  • No chemical injection into the walls
  • Progressive drying of the affected walls

Mains-powered

ATE LC15 – ATE LC15 wall drying device

How to install your ATE device

Watch the installation steps and read the manual for your model to choose its position and follow the installation requirements.

ATE LC15 features at a glance

  • Electromagnetic technology
  • Intended for rising damp
  • Made in France
  • Stated diameter: 15 m
ATE LC15 – ATE LC15 wall drying device

How does the ATE LC15 work?


Rising damp occurs when ground water travels through the pores of building materials. The ATE LC15 uses Electromagnetic technology intended to support the progressive drying of affected walls. Choose the model according to its coverage and the building’s layout.

Electricity consumption

The stated power of the ATE LC15 is approximately 0.75 W. Continuous operation represents a theoretical consumption of 6.57 kWh per year. The cost depends on the electricity tariff and the actual consumption of the device and its power supply.

Coverage suited to your building

The ATE LC15 can be considered for a home, cellar or business premises when damp is caused by capillary rise. Check that the affected zone lies within the stated 15 m diameter.

ATE LC15 specifications

  • Electromagnetic technology
  • Intended for rising damp
  • Made in France
  • Stated diameter: 15 m

Mains-powered

10-year manufacturer’s warranty

Advice for correct installation

  • Follow the position and distances specified in the manual
  • Use the instructions for your chosen model
  • Ensure appropriate ventilation in the building

Preparing for drying and decorating

Wall materials, finishes and ventilation influence drying. Follow the manual’s recommendations before renewing wall finishes.

Our devices are intended for rising damp. Water ingress, leaks and condensation require solutions appropriate to their causes.

CHOOSING YOUR DEVICE

ATE LC15 : a solution suited to your walls

01

Identify the source of damp

The device is intended for rising damp. Leaks, water ingress and condensation require measures specific to their cause. Identify the source of damp before choosing a treatment.

02

Understand the role of the device

Yes. This electromagnetic model uses the power supply specified by the manufacturer and operates continuously as described in its manual.

STATED COVERAGE

15 m diameter · 7.5 m radius

The stated diameter is 15 m, equivalent to a radius of 7.5 m. This is a coverage distance, not a floor area in square metres. Compare the proposed position with the affected walls and the layout of the building.

Ø 15 m7.5 m radius
03

Prepare the installation

Fixing the ATE requires two drilled holes for the wall plugs and supporting screws. Choose fixings suitable for the wall and follow the position, height and clearance instructions in the manual.

04

Choose compatible finishes

Wait until the substrate is suitable for the chosen finish. Materials, salts, coatings and ventilation influence drying; there is no single timescale that applies to every building.

CHOOSING YOUR DEVICE

ATE LC15: checks before you choose

Four checks to help you choose the model and prepare for installation.

01

Describe your building

Gather photographs of the affected walls and note the materials, floors and rooms involved. This information helps our team understand the layout.

02

Compare distances on a plan

Identify a possible installation point and measure the distance to the furthest affected walls. Compare these distances with the stated coverage rather than floor area alone.

MODEL COVERAGE

Ø 15 m

Stated diameter
Corresponding radius

7.5 m

This is a coverage distance, not a floor area in m².

03

Prepare the installation

ATE: mounting requires two drilled holes for the wall plugs and support screws. Prepare the specified power supply and fixings suitable for the wall, following the manual.

04

Plan the finishing work

Identify low-permeability coatings, salts and ventilation needs. Select renovation materials according to the masonry and the condition of the substrate.

Frequently asked questions about ATE LC15

Is this an air dehumidifier?

No. ATE LC15 is intended for walls affected by rising damp. It does not collect water in a tank or directly dehumidify the surrounding air.

What if there is also a leak or penetrating damp?

Have the source of that water ingress repaired. When several causes are present, addressing rising damp is only one part of the work needed.

Can I hide the device behind furniture?

Do not choose a position solely to hide it. First check the mounting requirements, clearances and access specified in the manual for ATE LC15.

When can I repaint or replaster?

When the substrate is suitable for the planned finish. The indicative timescale on this page is not a renovation date for every building; salts and existing coatings must also be considered.

Where can I check the price, finish and documents?

The shop page shows the available finishes, price and availability. The model manual gives the installation instructions. View the product page

Any questions?

Choosing between two models? Our team can help you compare coverage and installation requirements to select a device suited to your walls.